• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane can be a source of frustration. It could also be a chance to upgrade your glass to energy-efficient or insulated windows to benefit from improved comfort, increased resale value and reduced utility costs.

It's a project you can take on yourself for less than the cost of hiring an expert. You'll only require the right tools and a few hours of your time.

Glass

Replace your single-paned windows using tempered or insulated glass to increase the efficiency of your energy, reduce noise, and maintain the historic integrity of your home's older. The replacement of windows is easy and can be accomplished by anyone with basic hand tools. You will also require an additional window pane, glazier's tips, pliers, and latex glazing putty. If needed you can use a heatgun to warm the old putty. Wear safety goggles and gloves prior to starting. Working with broken glass could result in serious injuries.

Begin by removing any remaining broken pieces of glass. It is recommended to use pliers however, a flathead may be useful equally. Then, use a wooden chisel or putty knife remove the rest of the old putty around the frame and the sash. Work slowly and carefully, taking care not to damage the old window sash. It is a good idea to work using a sturdy ladder rather than on the ground and place someone on the sash to help hold it in place.

Once you've removed all the old putty, prepare the window frame for the new pane. To allow for seasonal expansion or contraction and contraction, subtract 1/8 inch from the measurements of width and height. These measurements can be sent to a home center or hardware store to have a piece cut of glass that is in stock to the correct size. You can also cut the glass by yourself if you have the right tools.

After installing the new pane after installing the new pane, put a tiny amount of caulking around the edges to make it weatherproof. Install a glazier's pointing on both sides of the frame. This will help secure the pane. The points should not be tight enough to cause friction between the frame and sash however they should not be loose.

Before applying the putty on the surface, you must knead it thoroughly until it is smooth and free of lumps. Then you can roll it into pencil-sized strips. The first strip should be placed to the corner of the frame, moving from one corner to the other to ensure it is even and smooth.

Glazier's Points

The glazier's points are small triangular pieces of metal that help secure glass into frames for windows without scratching or damaging the fragile surface. It's simple to learn how to use this secret tool and you can save money on the expense of a professional installation.

Once the old putty and glazier's points are removed Clean the frame thoroughly using a utility knife to get rid of any remaining traces. If necessary it is necessary to lightly sand the wood along grooves of the rabbets to smooth rough areas. If you decide to sand the wood, ensure you protect it with painter's tape to avoid accidental damage.

Take the dimensions of the frame and note down precise measurements. Take these measurements to an hardware store or home center, and have the new pane cut slightly smaller than the frame's opening. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Insert the new pane into the frame and push it in with your hands. Make use of the point of the chisel, or the back of the putty blade to tap in the glaziers' points as illustrated in Figure 11. After you're done, the points should be flush with the top edge of the pane. the raised shoulders of the points should be below the rabbet's lip. groove.

Apply a small amount of glazing compound on the edges of the new glass and into the rabbet grooves to seal and protect them. Allow this to dry and cure completely.

Once the glazing compound has dried and the glazing compound is dry, you can install the new window sash. The first step is to coat the wood with a thick coat of linseed oil. This will keep the new putty from taking up the moisture and deteriorating and cracking over time. Use a brush to apply this coat, or even the tip of the putty blade. Then, use the chisel on the back of the putty tool or the back of the putty handle to gently hammer the new sash or wooden glazier's point into the rabbet grooves. Repeat this process in intervals of 10 inches all around the frame.

Putty

A baseball thrown or a rock thrown in error, or a tree falling could result in a broken or cracked window pane. The majority of windows can be replaced by simply putting in a fresh piece. The glass is held in the position with a tiny metal clip, called the glazier's point, and putty. This compound is also referred to as glazing compound. Before you install a new pane, first remove the old one and clean the area with an abrasive and the pull-type paint scraper or a wood chisel. Wear safety glasses and gloves while you do this work. If the window is secured to the frame, you'll need make use of a heat gun to soften the adhesive before prying it free.

If you are planning to reinstall your original sash, you must remove the molding that supports the old pane. Sand the sash until it is flat and ready to receive new caulk. After the sash has been put back in place then, you can apply a silicone caulk to the glass. This will ensure that it won't leak over time or discolor.

Remove the glazing points from the rabbets, the grooves in the sash where the glass sits. If they're difficult to cut out, you can try holding a hand tool like a heat gun over them to soften them first. When using a heating tool, be careful to not scratch the sash or its railings.

Once the old glaze points and wooden putty are removed, make a bed for the new pane. Roll a rope with glazing compound between your fingers and then make it about 1/2 inch thick. Then, push it into the rabbets in which the glass will rest. The glass must be positioned against the putty on both sides. If you need to, lightly tap your glass into the rabbet with your thumb.

If the new pane has cracked, you can apply the silicone caulk or glass glue that is based on solvents to fill in the crack prior to pressing it in the sash. In other cases, you'll need to apply putty over the crack to create an impervious seal to keep water out. When the putty dries then clean the oily film off the glass using an abrasive and allow it to dry completely before painting. Paint before the putty has completely dried. It will not make a strong seal and could leak or discolor with time.

Paint

You might be worried about replacing a broken pane of glass. It's true that replacing a single pane glass doesn't have to be costly even if you do it your own. Even a double-paned window can be replaced at a fraction of the cost it will cost for a professional.

First, if you are working on a large window, make sure it is securely fixed to the frame. Using the proper tools and techniques to make this task relatively easy and fast.

If you're ready to begin with the removal of the old window by removing the metal glazing points that are connected to it. These are tiny metal triangles that act as "nails", holding the window within the frame. They are submerged under a bead of glazing putty that is then cured to form a solid, moulded wedge which holds the window sash replacement in place and conceals the edges.

After removing the old pane, clean the frame and the wood. Scrape off any paint that has been used and sand down the rabbet grooves where the glazing points were placed. Sand them to bare wooden surfaces so you can paint the frames the same shade. After sanding the wood you can apply a layer flax oil. This will help prolong the life of the frame.

Next, measure the size of the window's opening. You will need to take horizontal and vertical measurements of the entire opening, as well as the thickness of the old pane. To get the exact size of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass during seasons of change. Bring these measurements to the hardware or home improvement store and have a piece cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.