• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat multipla key 500 Key Fob Won't Work

A key fob for the Fiat 500 is a convenient method to open the doors and begin the car. However, there are many reasons why the fob won't be functioning. This could be due to a dead coin-battery water damage, problems with the receiver modules, and interference.

This listing is for a NEW replacement fiat 500 remote key programming Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to search for local locksmiths for your vehicle). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most frequent reason that the 500 key fob won't function is due to an inactive battery. Modern key fobs only have a limited range of operation and must be within only a few inches from the vehicle to function. If you are not within your vehicle and press the keyfob button, it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the coin-cell battery (Part Number CR2032) by a new one of a reliable brand, like Panasonic Duracell or Energizer. They can be found in your local hardware store, or online.

After you've replaced the battery of your coin cell, you can test it by standing close to your Fiat 500 and pressing the buttons. The parking lights should flash and the key fob will operate the lock and unlock switch.

If the fob's remote doesn't function after replacing the battery, it may have water damage that prevents it from communicating with the receiver module locked keys in car boot fiat punto your car. Water damage can occur in a variety of ways, from a light splash to submerging the fob into salt water at the beach. If you suspect your fob was exposed to water, try putting it in a dry rice bag to pull the moisture out. If this doesn't work, the fob might need to be reprogrammed by a professional auto locksmith or dealer.

Water Damage

Water damage can occur when you submerge the fob in the ocean or wash it in a machine. Saltwater can cause the circuit board to short and then die. It's not a good thing to let the fob get wet but don't give up even if you accidentally drop the fob in water, or fail to remove it from your pocket.

First, remove the battery from the fob. Before replacing the battery clean the electronic chip with isopropyl or similar products. Check the fob again to determine if it's functioning. If the fob doesn't work, it may need to be reset. This is typically done by a professional or dealer auto locksmith.

If your key is old and is not programmed for your car it is necessary to replace it completely. This is an easy process that can be completed by a professional locksmith for automotive use. The locksmith will require the key to be cut to match your car's ignition. They'll also have to reprogram the fob in your lost car keys fiat's system. This is a cost-effective and fast process that can be completed on the same day.

Receiver Module Issues

Your 500 key fob might not function because it's out of range. The remote's range is of 30 feet. So when you're too far away from your vehicle it won't be able to respond to your commands. It is possible to fix this by moving the remote closer to your car until it responds.

If your fob doesn't work after replacing the battery in the coin, also called a "button", "watch" or "button", it could be due to a problem with the circuit board inside. In the majority of cases, reprogramming your fob will solve the issue. You can find directions on how to start a fiat 500x with Key to do this for all automobiles by searching YouTube or checking out the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in their place. If they loose tension, they could stop the coin battery from sitting properly and can cause your remote to malfunction.

In rare instances the fob could be disconnected from your vehicle due to software or hardware issues. This can be a major issue, but you are able to usually fix it by visiting a local dealer or auto locksmith to have them reprogram your fob. In certain situations they might need to install the software again in your body control module too.

Interference

In addition to a dead coin battery The key fob may not be able to receive or transmit a signal due to interference. This is possible when the key fob is close to radio transmitters (cell phones or radar detectors) or any other source of electromagnetic radiation. The key fob might not work because of a weak connection to the buttons water damage or damage to the internal chips.

If the key fob suddenly stopped working, in the middle of the night or after trying every option at home to resolve it e.g. replacing the battery, reprogramming it and using the spare key fob, you could have a malfunctioning receiver module on your 500. The receiver module, located under the dashboard, is able to pick up radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's on-board system including the keyfob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable and then the positive cable. Then, reconnect the battery. This will erase any remaining electricity, and restart the computer in your car. This will help you get your key fob working again. If the problem persists you should consult an expert technician. They'll be able identify the root cause of your issues.